Kill switch relay

neandethal

Junior member
Location
oakham
Hi,
My recently acquired Jota doesn't have the relay wired into the kill switch.
Will any harm come from just using the key switch to stop engine.
Cheers Ian
 
The kill switch is meant to be for emergency use. Usually the ignition key is used to stop motorcycle engines. If the kill switch isn't connected, mine isn't since fitting a DMC 32 ignition system, it is not an MoT failure as it isn't part of the test. Having said that, I expect your Jota is MoT exempt anyway, so carry on using the key.
 
No harm at all ......... Like Mr Pauls above , mine became isolated upon fitting the DMC2 , which if I remember correctly does away with the messy connection block behind the tank which the relay feeds from ............ although I do have a vague memory of it becoming available again , maybe I plumbed the relay back in again somehow ........ or maybe there was an option for an ignition kill within the DMC2 anyway , and I had just disconnected the relay earlier on before fitting the DMC2 , because the wiring into that messy connector became brittle and worn ........... :unsure: .............

Yes , that was it ........ removed the relay because of the dodgy connections .... then when I fitted the DMC2 I had a working kill switch again ,,,,,,, I think .........

But in any case it doesn`t matter .......... except in emergencies ..................
 
Last edited:
I wired mine (not a triple, and not standard) to cut power to the coils but not the starter button (which I think is std?). So I can spin my motor without powering the coils when the plugs are out. Cheap insurance.
 
Originally, both the HKZ and BTZ triples used "engine stop relays". The HKZ version would ground the magneto when ignition was switched off, the BTZ version would cut current to the ignition. Most aftermarket ignition systems do away with these.

As the OP has neither specified which model "Jota" he has, nor which ignition system is fitted, I'm guessing an aftermarket battery powered system has been fitted and the original relay has simply been left to rot with nothing attached to it...

Please enlighten us.

piet
 
I should have mentioned earlier my experiences were with a CDI ( MHKZ ) system ..........

Not that it matters , and not that anyone would be particularly interested. ......... but I believe as mentioned before that I removed the stop relay as the wiring generally ( not just the relay ) going into that multi block connector was becoming brittle and generally tired .........

There wasn`t much free play in the wiring to cut back to a fresher length , so I dumped the relay as it`s wiring " doubled up " with other connections going into the block .... so removing the relay simplified things , and gave me a more secure fixing now that the worn connections were no longer doubled up .........

It was only supposed to be a temporary measure , but stayed that way for quite a while .......... I think I also remember that this meant the engine would continue to run after I had switched the ignition key to off ...... ( surprise surprise ) ......... I would have overcome this by eliminating engine tickover ...... so it died as soon as the throttle was shut ..........

All this was pre-DMC2 , obviously .........

I believe very early triples had no stop relay fitted , which meant the lawn mower generator which Laverda fitted was always " live " ...... so anyone who wanted a triple could walk up to a parked one , bump start it and ride off down the road ....... ( I think Dave Minton mentioned this once in an article ........ so take it with a pinch of salt if you wish ......... maybe this was just the early pre-production bike that he rode ) ........

I was quite proud of the DMC2 when I fitted it .......... I gutted the 1200`s tool tray behind the battery and rubber mounted a 1.5 mm or something thick sheet of stainless vertically in it`s place ........ mounted the DMC unit and matchbox rectifier onto that ...... fed the nice new wiring up past where that multi block connector used to be ......... and fashioned another sheet of stainless to fit onto the old black box mounting points to mount the coils onto .......... all connected with nice simple wiring and chunky new connectors .........

All neat and tidy , even if I say so myself .................

The only thing was the position of the coils on the mounting plate meant the whole thing had to be removed if you wished to lift the cam cover ....... ( lack of clearance ) .......... I was going to fashion a MK 2 plate , with the coils mounted further up and out of the way ......... but then I went and sold the bloody bike after forty years and a quarter million miles .......... :oops: ...............


I hope the current owner appreciates all the effort I put in ............... ( Generator pick up and coil plate wiring was starting to get a bit iffy though ....) ......
 
Last edited:
I should have mentioned earlier my experiences were with a CDI ( MHKZ ) system ..........

Not that it matters , and not that anyone would be particularly interested. ......... but I believe as mentioned before that I removed the stop relay as the wiring generally ( not just the relay ) going into that multi block connector was becoming brittle and generally tired .........

There wasn`t much free play in the wiring to cut back to a fresher length , so I dumped the relay as it`s wiring " doubled up " with other connections going into the block .... so removing the relay simplified things , and gave me a more secure fixing now that the worn connections were no longer doubled up .........

It was only supposed to be a temporary measure , but stayed that way for quite a while .......... I think I also remember that this meant the engine would continue to run after I had switched the ignition key to off ...... ( surprise surprise ) ......... I would have overcome this by eliminating engine tickover ...... so it died as soon as the throttle was shut ..........

All this was pre-DMC2 , obviously .........

I believe very early triples had no stop relay fitted , which meant the lawn mower generator which Laverda fitted was always " live " ...... so anyone who wanted a triple could walk up to a parked one , bump start it and ride off down the road ....... ( I think Dave Minton mentioned this once in an article ........ so take it with a pinch of salt if you wish ......... maybe this was just the early pre-production bike that he rode ) ........

I was quite proud of the DMC2 when I fitted it .......... I gutted the 1200`s tool tray behind the battery and rubber mounted a 1.5 mm or something thick sheet of stainless vertically in it`s place ........ mounted the DMC unit and matchbox rectifier onto that ...... fed the nice new wiring up past where that multi block connector used to be ......... and fashioned another sheet of stainless to fit onto the old black box mounting points to mount the coils onto .......... all connected with nice simple wiring and chunky new connectors .........

All neat and tidy , even if I say so myself .................

The only thing was the position of the coils on the mounting plate meant the whole thing had to be removed if you wished to lift the cam cover ....... ( lack of clearance ) .......... I was going to fashion a MK 2 plate , with the coils mounted further up and out of the way ......... but then I went and sold the bloody bike after forty years and a quarter million miles .......... :oops: ...............


I hope the current owner appreciates all the effort I put in ............... ( Generator pick up and coil plate wiring was starting to get a bit iffy though ....) ......
Hi Tony,

Off topic, as is the way - but you'll hopefully be pleased to hear that 'your' Mirage is undergoing a thorough rebuild and is expected to be back in action by the Spring - so the owner happily told me last week 😊
 
Hi Tony,

Off topic, as is the way - but you'll hopefully be pleased to hear that 'your' Mirage is undergoing a thorough rebuild and is expected to be back in action by the Spring - so the owner happily told me last week 😊

Thanks Alan .........

You may want to tell him total mileage was 226,000 when I sold it ..... ( the original speedo had worn out , so the replacement didn`t indicate anything like that ) ........... So he can start adding to that mileage next year , hopefully ....... (y) ..............

( This will be just the second re-birth of 1200 * 1637 by the way ........ The first at 113,000 miles ..... and now the second at 226,000 or whatever the mileage is at the moment ...... ) ..............

Good bikes aren`t they ?

Cheers , Tony
 
Last edited:
Thanks Alan .........

You may want to tell him total mileage was 226,000 when I sold it ..... ( the original speedo had worn out , so the replacement didn`t indicate anything like that ) ........... So he can start adding to that mileage next year , hopefully ....... (y) ..............

( This will be just the second re-birth of 1200 * 1637 by the way ........ The first at 113,000 miles ..... and now the second at 226,000 or whatever the mileage is at the moment ...... ) ..............

Good bikes aren`t they ?

Cheers , Tony
Built to be ridden and enjoyed 👍🏍😎

I've shared your message with Steve, the current owner.

Watch this space.... 😁
 
Modern ignitions for the Laverda reduce markedly the amount of current carried across any switching contacts, ie ignition switch and essential to me, RHS RUN/STOP switch. Not the case with factory BTZ, which hammered everything, from motor pinking to killing batteries..... still out of the shocking terrible comes the good....time line aligned, DMC/Todd Boyer/SilentHektik?/iis/sache/et al and others that had variable value. j.
 
Back
Top